Proline Filter Sand Owners Manual
Posted By admin On 08.01.20They have been used by private pool owners for many years and are great for keeping water free of dirt and debris. These swimming pool filters feature a series of chambers which hold special pool grade sand. As the pools pump propels water through the filter system, dirt and other debris are trapped in the spaces between the sand particles. They are thus prevented from moving on as the cleansed water continues through the sand, exiting through the bottom layer and returning to the swimming pool. The DE Filter: DE is short for Diatomaceous Earth. DE is an organic powder that is actually mined fossilized exoskeletons of tiny diatoms.
Its the most effective filter, getting smaller particles from the water. It filters down to 5 microns.
The DE powder is normally put into the skimmer, from which point it is sucked into the DE filter and coats the DE filter grids, which consists of 68 grids in the filter housing. The DE substance then catches the dirt and debris. The amount of DE used is based on the size and specific model of DE filter. For a quality swimming experience make sure to seek out a pool cleaning professional for all pool filter cleaning. Savvy pool owners understand that the importance of swimming pool filters is undeniable.
Pool filters remove debris and pollutants that would otherwise cause dirty, cloudy water. However, pool filters for inground swimming pools are important for more than just aesthetic reasons, as contaminants such as bacteria can cause illness while cloudy water creates ideal conditions for algae growth. Gallery of proline pool filter owners manual.
Proline High Rate Sand Filter Owners Manual
. 19 Answers SOURCE: hayward S-180 filter takes 150lbs, S-210 takes 200lbs not familur with the S-200. To change sand you have to remove the vari flow valve on top. Lifeguard instructors manual. You can either unplumb the filter and roll it over on its side and try washing the sand out or try scooping it out upright. Whatever you do dont damage the laterals on the bottom of the filter.
When refilling with sand you want to make sure all the laterals are undamaged and in the down position. I always fill the filter half full of water to keep the sand from damaging the laterals while re-filling the filter with sand.
Make sure you use pool filter sand and not play sand! Posted on Apr 30, 2009. 640 Answers SOURCE: I happen to have a copy of the users manual for this. These are the instructions for operating your filter. Be sure correct amount of filter sand media is in tank and that all connections have been made and are secure. Depress Vari-Flo control valve handle and rotate to BACKWASH.
position. (To prevent damage to control valve seal, always depress handle before turning.) 3.
Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with water. WARNING: ALL SUCTION AND DISCHARGE VALVES MUST BE OPEN WHEN STARTING THE SYSTEM. FAILURE TO DO SO COULD CAUSE SEVERE PERSONAL INJURY. Once water flow is steady out the waste line, run the pump for at least 2 minutes.
The initial back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear—about 1/2 to 1 minute. Turn pump off, set valve to FILTER position and restart pump.
Proline Pool Filter Parts
Your filter is now operating in the normal filter mode, filtering particles from the pool water. Adjust pool suction and return valves to achieve desired flow.
Check system and filter for water leaks and tighten connections, bolts, nuts, as required. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping system). As the filter removes dirt and impurities from the pool water, the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 8-10 PSI (0.55-0.69 BAR) higher than the initial 'clean' pressure you noted, it is time to backwash (clean) the filter (see BACKWASH under Filter Control Valve Functions.) Posted on May 24, 2010. I used to work in a municipal swimming pool.
325,000 gallons! It sounds like you have the sand filter on to clean if water is coming out of the waste line. That is called 'back flow'. Basically, the water from the pool comes into the top of the filter and the muck settles on the top. You need to add Gypsum (Aluminium Sulphate) to the water which is a floculant. This makes organic material form into a layer on top of the sand.
The flocculated layer further adds as a filter. You need to regulate the flow of water into the filter as too fast and you force sand into the pool. When you clean the sand filter, you do a back flow. So by altering valves, you put the water from the pump into the bottom of the filter and the water lifts the muck and dirt off the top of the sand and discharges it to waste. It is important to also regulate the flow as too much will discharge the sand. That happened in our municipal pool and discharged 6 tons of sand in the space of 2 years. Your owners guide is here.
Proline Pool Filters
Take a look at the pipes, valves and pump and work out where the flow is going to. Jul 03, 2016. If you took 'Pump' apart, you wouldn't have found broken laterals. You will need to open up the 'Filter' to find laterals. If sand is ending up in the pool, you either have a broken component within the filter or you have an overfilled filter tank and during backwash sand is lifted up into the valve, and upon returning valve position back to 'Filter' the residual is blown back to pool via the return inlet. If this is the case that is why always follow label / owners manual directions as to Quantity of media to add.
More is not necessarily always better! Jun 19, 2014.